When you’re fitting fire protection systems into a commercial building, even a small mistake can create a much bigger problem. A pipe needs to pass through a concrete wall or floor, but where exactly should you drill?

That’s where good planning matters. Fire Services Core Drilling helps create accurate openings for fire pipes and other equipment, but the work needs to suit the building, the services and the fire protection requirements.

What Is Fire Services Core Drilling and Why Does It Matter?

Fire protection systems often run through different floors, walls and service areas. Sprinkler pipes, hydrant lines and other fire services need clear paths through the building structure. Core drilling creates those openings without breaking up large sections of concrete.

If you’re planning a commercial installation, our Fire Services Core Drilling service can help with accurate concrete openings for your project.

Think about a new office building with a fire sprinkler system across several floors. The installer needs to connect the pipework between levels, which means creating openings through concrete slabs. Every opening needs the right position and diameter.

That’s why I wouldn’t treat this work as just another hole in the concrete. The drilling location can affect other services, structural elements and the fire protection system.

Before work starts, check the building plans and confirm the penetration requirements with the relevant contractors. The Australian National Construction Code provides the framework for fire safety and service penetrations through fire-resisting building elements. Always check the edition and Victorian variations that apply to your project.

Here are seven things I’d check before getting the drilling team on site.

1. Fire Services Core Drilling Starts With the Right Drawings

I always recommend starting with the latest construction and fire services drawings. They show where the pipes need to run and help the drilling team understand the proposed opening locations.

Don’t rely on an old drawing or a quick measurement taken during a site visit. Construction sites change, and another contractor may have already installed services in the planned drilling area.

Check these details first:

  • Pipe measurements: Confirm the actual outside diameter of each pipe.
  • Drilling locations: Mark the exact position of every opening.
  • Floor and wall thickness: Check the concrete depth before selecting equipment.
  • Nearby services: Look for existing electrical conduits, plumbing and mechanical services.
  • Installation clearance: Allow room for sleeves and the specified fire-stopping system.

One small detail can change the entire job. For example, a pipe may need extra space for its sleeve or fire protection material. If you only measure the pipe, you could end up with an opening that’s too small.

Get the fire services installer, builder and drilling contractor to agree on the positions before work begins.

2. Scan the Concrete Before Fire Services Core Drilling

You can’t see what’s hiding inside a concrete slab just by looking at its surface. Reinforcing bars, electrical conduits and post-tensioning cables may sit directly in the proposed drilling path.

This is why concrete scanning deserves attention before any cutting starts.

A concrete scanner can help identify embedded objects and give the team a clearer picture of what’s inside the slab. The exact results depend on the scanning equipment, concrete conditions and the objects present, so scanning doesn’t replace structural approval.

I’d pay particular attention to:

  • Reinforcing steel: Avoid cutting reinforcement without approval from the structural engineer.
  • Post-tensioning cables: Never drill through a suspected cable without proper identification and approval.
  • Electrical conduits: Check for hidden electrical services before drilling.
  • Existing pipes: Look for water and other service lines that may cross the proposed opening.

Imagine drilling through a slab only to discover that a cable runs directly through the opening. That’s a problem nobody wants halfway through an installation.

For Fire Services Core Drilling, scanning helps the team make better decisions about drilling positions. If the proposed location isn’t suitable, ask the project engineer to approve an alternative.

3. Check Fire-Rated Walls and Floors Before Drilling

This is one detail you really don’t want to overlook.

Commercial buildings often use fire-rated walls and floors to slow the spread of fire and smoke. These building elements help separate different areas and give people more time to respond during an emergency.

When a fire pipe passes through one of these elements, the opening needs suitable fire protection.

For example, a sprinkler pipe may pass through a concrete floor to connect two levels of a building. Once the installer puts the pipe through, a gap may remain around it. You need an approved fire-stopping solution that suits the actual penetration.

Before drilling, confirm:

  • Whether the wall or floor has a required Fire Resistance Level (FRL).
  • Which fire-stopping system suits the pipe and building element.
  • Whether the proposed system has the necessary test evidence.
  • Who will install and document the fire stopping.

AS 4072.1 and AS 1530.4 are important references for relevant tested service penetration systems and fire resistance testing.

Remember, a neat opening doesn’t automatically mean a compliant installation. The pipe, building element and fire-stopping arrangement must work together.

4. Choose the Correct Hole Size for Fire Services Core Drilling

Getting the hole size right sounds simple, but there’s more to it than measuring the pipe.

The installer may need additional space for a sleeve, pipe movement or the specified fire-stopping product. The approved system will help determine the opening requirements.

Here’s what I would check before confirming the drilling diameter:

What to checkWhy it matters
Pipe diameterEstablishes the basic opening requirement
Sleeve sizeAllows room for the specified sleeve
Fire stoppingDetermines the required gap and protection
Concrete thicknessHelps select the correct drilling setup
Opening positionKeeps the pipe aligned with the installation plan

Don’t make the hole larger just to give the installer extra room. An oversized opening can create more work and may not suit the tested fire-stopping arrangement.

Likewise, a hole that’s too tight can make pipe installation difficult.

For Fire Services Core Drilling, I recommend confirming the final diameter with the fire services contractor before the drilling team starts. A quick discussion can prevent unnecessary adjustments later.

5. Select the Right Equipment and Drilling Method

Not every concrete drilling job needs the same setup. A small opening through a thin wall is very different from a large penetration through a thick reinforced slab.

Diamond core drilling is a common choice for this type of work. It uses a diamond-tipped barrel to cut a clean, circular opening through concrete.

Depending on the job, the drilling team may need:

  • A suitable diamond core bit for the required diameter.
  • A stable drilling rig for accurate positioning.
  • Equipment that can handle the concrete thickness.
  • Water collection equipment for wet drilling.
  • Suitable dust controls and site protection.

Wet diamond drilling uses water to cool the cutting area and control dust. However, the team also needs to manage the resulting slurry. They should protect nearby electrical equipment, finished surfaces and occupied areas.

Access matters too. A tight plant room or busy service corridor may need a different setup from an open construction floor.

When arranging Fire Services Core Drilling, share the opening sizes, concrete thickness and site conditions with the contractor. That information helps them prepare the right equipment instead of making assumptions on the day.

6. Plan Site Access and Coordinate With Other Trades

A drilling job rarely happens in isolation. Fire services contractors often share the site with electricians, plumbers, mechanical contractors and builders.

If everyone works in the same area without a clear plan, delays can follow.

For example, the drilling team may arrive ready to create an opening, only to find that another contractor has filled the area with equipment or installed services across the planned drilling position.

You can avoid many of these issues by sorting out a few practical details beforehand:

Access and working space: Make sure the team can bring its equipment to the drilling location.

Nearby workers: Keep people away from the drilling area, including the space directly below floor penetrations.

Services isolation: Arrange suitable isolation where nearby live services create a risk.

Noise and working hours: Check site rules, particularly in occupied offices and commercial buildings.

Water and slurry: Agree on how the team will collect and remove drilling waste.

I also recommend confirming who will prepare the area and who will clean it afterwards. It sounds like a small detail, but it avoids the usual confusion when several trades share one workspace.

Good coordination makes Fire Services Core Drilling easier to manage and helps the rest of the installation stay on schedule.

7. Complete Fire Stopping and Check the Finished Work

Once the drilling team creates the openings, there’s still important work to complete.

The fire services installer needs to fit the pipes, and the contractor responsible for fire stopping must protect any required fire-rated penetrations using a suitable system.

Don’t leave this part until the last minute. The fire-stopping arrangement should already form part of the installation plan.

Before signing off, check:

  • Whether the pipe sits correctly within the opening.
  • Whether the installed fire-stopping system matches the approved details.
  • Whether the installer has followed the product instructions.
  • Whether photographs and installation records are available.
  • Whether the relevant inspection and approval requirements have been met.

I would also keep a record of each penetration’s location, the service passing through it and the fire-stopping product used.

This information helps building owners and maintenance teams identify the correct arrangement if they need to inspect or modify the services later.

The drilling itself may take a short time, but the finished penetration needs the same attention as the rest of the fire protection installation.

Common Fire Services Core Drilling Mistakes to Avoid

Most drilling problems start before anyone switches on the machine. A missing drawing, an unchecked slab or a poorly planned opening can create unnecessary work.

Here are a few mistakes worth watching:

MistakeWhat can happen
Skipping concrete scanningThe drill may hit hidden services or reinforcement
Guessing the opening sizeThe pipe or fire-stopping system may not fit
Ignoring fire ratingsThe penetration may affect fire protection
Using outdated drawingsThe drilling position may clash with installed services
Poor site coordinationOther trades may face delays
Forgetting documentationFuture inspections become harder

The best way to avoid these problems is to bring the drilling contractor into the planning stage. Don’t wait until the fire services installer needs an opening immediately.

Why Melbourne Projects Need Careful Core Drilling Planning

Melbourne construction projects cover everything from office developments and warehouses to apartment buildings and industrial facilities. Each site has its own concrete structure, service layout and access challenges.

A warehouse may need several large openings for fire hydrant pipework, while an office building may need smaller penetrations across multiple floors.

Both jobs need accurate measurements and a clear understanding of the building structure.

Experienced drilling contractors can assess the proposed locations, discuss access requirements and select suitable equipment for the work. They can also coordinate with the project team when a proposed opening needs further review.

For Fire Services Core Drilling, early communication is often the difference between a smooth installation and an avoidable site delay.

Conclusion

A successful fire services installation starts well before the drilling machine reaches the concrete. You need the right drawings, accurate measurements, concrete scanning and a clear plan for protecting fire-rated walls and floors.

Fire Services Core Drilling also needs proper coordination with other trades and a suitable fire-stopping arrangement once the pipes go in.

If you’re planning a commercial project in Melbourne, don’t leave these details until installation day. Get the drilling requirements sorted early and give every contractor a clear plan to follow.

Need accurate concrete openings for your next project? Get in touch with our team to discuss your requirements and arrange professional core drilling support.

Frequently Asked Questions

1. What is Fire Services Core Drilling used for?

Fire Services Core Drilling creates circular openings through concrete walls, floors and slabs. Contractors use these openings to install sprinkler pipes, hydrant lines and other fire protection services.

2. Do I need concrete scanning before core drilling?

Scanning helps identify reinforcement, post-tensioning cables and concealed services before drilling. It gives the team useful information about the proposed location, although it cannot guarantee that every hidden object will be detected.

3. Can you core drill through a fire-rated concrete floor?

Yes, but you need to check the floor’s fire performance requirements first. After installing the pipe, the responsible contractor must use a suitable fire-stopping system that meets the applicable requirements.

4. How do I know what size core hole I need?

Start with the pipe’s outside diameter, then check the sleeve requirements and the approved fire-stopping details. Your fire services contractor should confirm the final opening size before drilling begins.

5. Does diamond core drilling damage surrounding concrete?

Diamond core drilling creates a circular opening and generally causes less surrounding damage than breaking concrete with heavy impact tools. However, the drilling team still needs to check the structure and choose the correct drilling position.